Instructions on how to use the PointMaster

Or call 0845 116 0284 *

The Point Master is a fast & efficient device for applying most types of mortar & floor tile grout directly to the joint. The nozzle is made from hard wearing stainless steel & will tolerate limited adjustment to suit different joint widths.

If you would like to open and print our instruction sheet click the box below

Instruction sheet

1. Mixing your mortar

Thorough mixing is essential & is best achieved with a cement mixer. However, vigorous hand mixing can achieve equally good results.

The Point Master is suitable for most sands, including medium sharp sand mixes. However, very gritty sands may not be suitable.

Avoid using Monofilament sand, as this has no fine particles (for example kiln dried paver sand).

Be aware of using wet sand - you may not need to add as much water as you think (See "Common Mistakes" Below).

Best results are obtained by using a relatively soft sand & a good quality plasticiser.

Mix the sand & cement together in a cement mixer or suitable mixing vessel such as a barrow or bucket.

Add plasticiser directly to the mix (not into your water container)

Add water in gradual stages, mixing thoroughly each time.

Important: Do not add the full amount of water until your mixing is nearly complete - (Add only 80-90%).

mixing thoroughly BEFORE the full amount of water is added will allow the plasticiser to add tiny air bubbles to the mortar. After thorough mixing, add more water until the correct consistency is achieved.

Carry out a quick test with the Point Master. You will soon become familiar with the consistency required for easy use.

The use of plasticiser in mortar is standard practice & not a special requirement of the Point Master.

2. A step-by-step guide to using the PointMaster

1. If necessary, adjust the nozzle* to fit inside the mortar joint.

2. ‘Liven up’ the mortar. A quick stir is usually sufficient.

3. Don’t completely fill the Point Master until you are familiar with using it.

4. Hold the Point Master just behind the nozzle, place your other hand on the ‘end’ of the handle grip. Keep the Point Master out to one side of you (not in front of you).

5. A slight twisting action of the handle whilst applying pressure will help to encourage an even flow.

6. Before each refilling, shake or gently tap out unused mixture.

7. Fill the Point Master & use immediately, holding the nozzle square to the joint (see images 1 and 2 below).

8. Slightly overfill the joints using a series of movements along the joint, or with a continuous sliding motion.

9. Wash out periodically. Clean the tool thoroughly after use.

* To adjust the nozzle (on the tool), use pliers on each side of the nozzle only. Straighten the long sides if they have bowed inwards. For specific jobs, the short sides of the nozzle can be customised, see image 3 below.

3. Correct orientation of the tool for precise application

Use the PointMaster square to the joint

Tool is at right angles to the mortar joint



4. Watch the mortar mixing video

Click the "Play" button below to watch our online video on how to mix correct mortar for the Point Master

Can't see the video? Click HERE and let us know

5. Some useful pointing tips

Old joints should be raked back to at least 15-20mm, or deeper for paving, then brushed or washed thoroughly to remove any dust. A power washer will often remove lime mortar from brickwork or dry mixed mortar from patio joints.

For wall pointing, fill the bed joint first and then fill the perpendicular (upright) joints above it. This stops sagging.

After applying new mortar, leave the unfinished pointing to stiffen slightly, finish the joint by smoothing off with a trowel or pointing iron. Lightly brush over before the mortar has set hard.

Do not use old cement that has become ‘lumpy’. Avoid mixing too much mortar, especially in hot weather. Freshly mixed mortar is more effectively applied than that which has partly cured.

Different sands & mixes will flow differently, therefore it is important to find the right consistency.

Standard mix for wall pointing: 5 parts building sand, 1 part cement, add plasticiser to manufacturers instructions. Use maximum amount when mixing by hand. Patio slabs or exposed brickwork, you may need a stronger mix. For example - 3:1 sand / cement.

A good quality liquid plasticiser is required. Add this directly into the mix, not into the water.

For non structural applications, washing-up liquid could be used as a substitute for commercial plasticiser. An approximate measure would be one third (1/3) of a teaspoon of concentrated liquid for 5 shovels of sand and cement mix.

Bagged pre-mixed mortar may require a small amount of additional plasticiser, especially when mixing by hand. Thorough mixing is still required as this will add air and make the mortar easier to use.

Lime Mortar (typically) 2.5 sand / 1 lime: Plasticiser is not required, but the mixing time should be longer. The mix should be allowed to sit for a period after initial mixing, to allow it to self-bulk - then remix and use.

Common Mistakes - Flooding the Mix

Adding too much water in the early stages of the mixing process is a common mistake. This will stop the plasticiser from working properly and will result in a flat mix that does not flow correctly. It may also cause the water to separate. If this happens, add more sand, cement & plasticiser to dry the mix, mix thoroughly in this drier state for several minutes, then add water to achieve the correct consistency.

6. Replaceable parts & safety

Replaceable Parts

The rubber piston washer is not designed as a seal and so does not make a tight fit. This part will require replacing when it no longer protrudes from the side edge of the plunger. Slide a thin bladed screwdriver halfway down the side of the washer, pull the washer up so that you can stretch it off. Stretch a new washer over & into the groove (the end cap is non removable).

The Point Master stainless steel nozzles & piston washers are both replaceable items. You can order these by calling us on: +44 (0) 208 133 5396 or on 0845 116 0284*. Or simply use our online shop.

visit shop



Health & Safety

The edges of the Point Master’s nozzle may become sharp with use, so care should be taken to avoid these sharp edges. In this respect, protective gloves are recommended. In accordance with standard building regulations, Personal Protective Equipment (PPE) should be used.nutes, then add water to achieve the correct consistency.

Image of the Pointmaster pointing gun tool

What applications can I use it for?

It is suitable for most applications using regular cement mortar, lime mortar and grout for flooring. It works with most common mix ratios, and is fine with mortar colourant.

X

Changes to 0845 numbers

Our older telephone number: 0845 116 0284 is no longer local rate from anywhere in the UK.

Calls now cost 5p per minute plus your standard network rate

Please call us on +44 (0) 208 133 5396 which is our standard UK geographical number.

The Point Master team.